What are the skills and tricks of Dongguan Dongguan large-scale talk about precision machining?
by：Foxron
2021-11-29
Nowadays, with the rapid development of various industries in the market, it has been recognized and used by everyone. This is enough to prove how important the existence of this industry is. When we are not in contact with this industry, we must be right to it. Without a certain understanding, Dongguan precision machining is the same, so what are the skills and tricks in precision machining?
Tip 1: Remove the jaws of the vise, and process two M4 threaded holes. Put two 1.5mm thick steel plates that are flush with the jaws, and use aluminum countersunk rivets to rivet the hard 0.8mm thick. The brass plate 3 is fastened to the jaws with M4 countersunk screws 1 to form a durable soft jaw. In this way, the hardware parts can be protected from being clamped, and they are interchangeable.
Tip 2: Using a magnet to pick up small parts (fee parts) is inconvenient to suck and take. You can suck an iron plate 2 under the magnet 1, which can not only suck a lot of small parts, but also pull the iron plate apart. It will automatically pour into the collection box immediately. It is not very touching, but it is very suitable.
Tip 3: When the pulley is driving, the pulley often slips with the axle. Use ￠15~18mm dimple drill bit to draw a series of dimples on the axle, which can form adsorption force, avoid slipping and turn waste into treasure. The boss will reward of.
Tip 4: When the hex wrench has a short handle and cannot be used to exert force, you can insert the wrench into the groove from a section of the milling groove, which can be used as a long handle.
Tip 5: There is a saying about tightening the workpiece by positioning and then clamping, but for a workpiece, clamping and then positioning, because the workpiece will definitely be deformed during clamping, it should be clamped and then positioned. Regarding the 6-point positioning, seek to limit its freedom.
The above are the skills and tricks in Dongguan precision machining. We can use these small skills to make our machining more convenient, less troublesome, and allow us to reduce labor and not spend so much time. And energy, we can learn to use it.
Tip 1: Remove the jaws of the vise, and process two M4 threaded holes. Put two 1.5mm thick steel plates that are flush with the jaws, and use aluminum countersunk rivets to rivet the hard 0.8mm thick. The brass plate 3 is fastened to the jaws with M4 countersunk screws 1 to form a durable soft jaw. In this way, the hardware parts can be protected from being clamped, and they are interchangeable.
Tip 2: Using a magnet to pick up small parts (fee parts) is inconvenient to suck and take. You can suck an iron plate 2 under the magnet 1, which can not only suck a lot of small parts, but also pull the iron plate apart. It will automatically pour into the collection box immediately. It is not very touching, but it is very suitable.
Tip 3: When the pulley is driving, the pulley often slips with the axle. Use ￠15~18mm dimple drill bit to draw a series of dimples on the axle, which can form adsorption force, avoid slipping and turn waste into treasure. The boss will reward of.
Tip 4: When the hex wrench has a short handle and cannot be used to exert force, you can insert the wrench into the groove from a section of the milling groove, which can be used as a long handle.
Tip 5: There is a saying about tightening the workpiece by positioning and then clamping, but for a workpiece, clamping and then positioning, because the workpiece will definitely be deformed during clamping, it should be clamped and then positioned. Regarding the 6-point positioning, seek to limit its freedom.
The above are the skills and tricks in Dongguan precision machining. We can use these small skills to make our machining more convenient, less troublesome, and allow us to reduce labor and not spend so much time. And energy, we can learn to use it.
Custom message
Tel : 86 769 3325 6035 / 86 769 8306 2140
Fax : +86 769 85634781
E-mail : 
Wechat//whatsapp : +86 189 3818 5885
Address : Wentang Industrial Zone, East District, Dongguan, Guangdong 
Zip code : 523121
